John Deere 4400 Specifications - John Deere 4400 Specs

info
122o↔0oF [50o↔-17oC]: : JD Hy-Gard
80o↔-40oF [26o↔-40oC]: : JD Lo Vis Hy-Gard
Production
Manufacturer: John Deere
Factory: Augusta, Georgia, USA
Capacity
Fuel: 10 gal [37.9 L]
Hydraulic system: 6.3 gal [23.8 L] (gear), 6.8 gal [25.7 L] (hydro)
Front axle: 4.7 qts [4.4 L]
3-Point Hitch
Rear Type: I
Rear lift (at 24"/610mm): 2,200 lbs [997 kg]
Power Take-off (PTO)
Rear PTO: independent
Clutch: wet disc
Rear RPM: 540
Engine RPM: 2100@2700
Mid PTO: optional
Mid RPM: 2100
Dimensions & Tires
Wheelbase: 68 inches [172 cm]
Weight: 2,900 lbs [1315 kg]
Front tire: 7.00x14
Rear tire: 11.2x24
4400 Serial Numbers
Location: Serial number plate on front-right tractor frame, above front wheel.
John Deere 4400 Power
Engine (gross): 35.7 hp [26.6 kW]
Engine (net): 33.7 hp [25.1 kW]
Gear PTO (claimed): 29.5 hp [22.0 kW]
Hydro PTO (claimed): 28.5 hp [21.3 kW]
Mechanical
Chassis: 4x4 MFWD 4WD
Differential lock: mechanical
Steering: power
Brakes: differential wet disc
Cab: Two-post ROPS
Hydraulics
Type: open center
Capacity: 6.3 gal [23.8 L] (gear), 6.8 gal [25.7 L] (hydro)
Pressure: 2500 psi [172.4 bar]
Valves: 2
Pump flow: 8.3 gpm [31.4 lpm]
Total flow: 13.3 gpm [50.3 lpm]
Steering flow: 5 gpm [18.9 lpm]
Electrical
Ground: negative
Charging system: alternator
Charging amps: 40
Battery
Number: 1
Cold-cranking amps: 500
Volts: 12
info
Power (gross): 35.7 hp [26.6 kW]
Fuel system: direct injection
Air cleaner: dry
Pre-heating: air heat
Compression: 18:1
Rated RPM: 2700
Idle RPM: 950-2810
Operating RPM: 950-2700
Starter volts: 12
Starter power: 1.9 hp [1.4 kW]
Oil capacity: 4.5 qts [4.3 L]
Oil change: 200 h
Coolant capacity: 6.1 qts [5.8 L]
Engine Detail
Yanmar 3TNE88, diesel, 3-cylinder, liquid-cooled, 100.2 ci [1.6 L]
info
Speeds: With 11.2-24 rear tires.
Transmission
Transmission: SyncReverser
Type: partially synchronized
Gears: 12 forward and reverse
Clutch: wet discs, two clutch packs with nine four-inch discs each
Oil capacity: 25.2 qts [23.8 L]
Four gears (1-4) in three ranges (A-C) with left-hand reverser on steering column. Gears may be shifting on the move, using the clutch. Tractor must be stopped, and clutch used, to shift range.
info
Next model: John Deere 4410
Series next: John Deere 4500
Series back: John Deere 4300
Dimensions
Weight (shipping): 2,900 lbs [1315 kg]
Drawbar capacity: 562 lbs [254 kg]
Front axle load: 3,197 lbs [1450 kg]
Rear axle load: 4,409 lbs [1999 kg]
Wheelbase: 68 inches [172 cm]
Length: 117 inches [297 cm]
Width: 50 inches [127 cm]
Height (hood): 53.3 inches [135 cm]
Height (ROPS): 84 inches [213 cm] (fixed), 90 inches [228 cm] (folding)
Clearance (rear axle): 13.4 inches [34 cm]
John Deere 4400 Tires
Ag front: 7.00x14
Ag rear: 11.2x24
info
Next model: John Deere 4410
Series next: John Deere 4500
Series back: John Deere 4300
60" Mower deck
Type: mid-mount John Deere
Cutting width: 60 inches [152 cm]
72" Mower deck
Type: mid-mount John Deere
Cutting width: 72 inches [182 cm]
Loader
Loader type: John Deere 430
Height (to pin): 101.4 inches [257 cm]
Clearance, dumped bucket: 78.3 inches [198 cm]
Dump reach: 25.6 inches [65 cm]
Dump angle: 45
Reach at ground: 57.5 inches [146 cm]
Rollback angle: 30
Breakout force (at 800mm): 3,299 lbs [1496 kg]
Lift to full height (at 800mm): 1,259 lbs [571 kg]
Raise time to height: 3.5 s
Bucket dump time: 1.8 s
Lowering time: 2.5 s
Rollback time: 2.3 s
Backhoe
Backhoe type: John Deere 48
Weight: 1517 lbs [688 kg]
Transport height: 81 inches [205 cm]
2-Foot flat digging depth: 102 inches [259 cm]
Reach from pivot: 133 inches [337 cm]
Loading height: 82 inches [208 cm]
Bucket Rotation: 180
Swing Arc: 180
Bucket force: 3730 lbs [1691 kg]
Dipperstick force: 2435 lbs [1104 kg]