FastFix DB
Search for Workshop, Owner, Service and Parts Manuals
info | |
The Deere 4100 was available in a Narrow version which could not be equipped with a mid-PTO. |
Production | |
Manufacturer: | John Deere |
Factory: | Augusta, Georgia, USA |
Original price (USD), $13,500 (2003 ), |
Capacity | |
Fuel: | 5.8 gal [22.0 L] |
Gear Hydraulic system: | 2.5 gal [9.5 L] |
Hydro Hydraulic system: | 3.3 gal [12.5 L] |
Front axle: | 3.6 qts [3.4 L] |
3-Point Hitch | |
Rear Type: | I |
Rear lift (at 24"/610mm): | 930 lbs [421 kg] |
Power Take-off (PTO) | |
Gear Rear PTO: | transmission |
Hydro Rear PTO: | independent |
Rear RPM: | 540 |
Mid RPM: | 2100 |
Dimensions & Tires | |
Wheelbase: | 58 inches [147 cm] |
Weight: | 1517 to 1565 pounds |
Front tire: | 5.00-12 |
Rear tire: | 9.5-16 |
4100 Serial Numbers | |
Location: | Serial number tag on the right side of the John Deere 4100 tractor frame, above the front axle. |
John Deere 4100 Power | |
Engine (net): | 19 hp [14.2 kW] |
Engine: | 20 hp [14.9 kW] |
Hydro PTO (claimed): | 16 hp [11.9 kW] |
Gear PTO (claimed): | 17 hp [12.7 kW] |
Mechanical | |
Chassis: | 4x4 MFWD 4WD |
Differential lock: | mechanical |
Steering: | power |
Brakes: | differential wet disc |
Cab: | Two-post ROPS. |
Hydraulics | |
Type: | open center |
Gear Capacity: | 2.5 gal [9.5 L] |
Hydro Capacity: | 3.3 gal [12.5 L] |
Pressure: | 2418 psi [166.7 bar] |
Total flow: | 5.1 gpm [19.3 lpm] |
Electrical | |
Ground: | negative |
Charging system: | alternator |
Charging amps: | 20 |
Battery | |
Number: | 1 |
Cold-cranking amps: | 433 |
Volts: | 12 |
info | |
Bore/Stroke: | 2.91x3.07 inches [74 x 78 mm] |
Power: | 20 hp [14.9 kW] |
Fuel system: | direct injection |
Air cleaner: | dry |
Pre-heating: | glow plugs |
Compression: | 23.5:1 |
Rated RPM: | 2650 |
Idle RPM: | 1025-2860 |
Torque: | 39.7 lb-ft [53.8 Nm] |
Starter volts: | 12 |
Oil capacity: | 2.3 qts [2.2 L] |
Coolant capacity: | 2.5 qts [2.4 L] |
Engine Detail | |
Yanmar 3TNE74, diesel, 3-cylinder, liquid-cooled, 61.4 ci [1.0 L] |
info | |
Speeds: | With 9.5-16 rear tires. |
Transmission | |
Type: | partially synchronized |
Gears: | 8 forward and 4 reverse |
Oil capacity: | 9.2 qts [8.7 L] |
Four speeds with high, low, and reverse ranges. Gear shifts can be made while in motion using the clutch. Tractor must be stopped to shift ranges. |
info | |
Previous model: | John Deere 670 |
Next model: | John Deere 4110 |
Series next: | John Deere 4200 |
Dimensions | |
Gear Weight: | 1517 lbs [688 kg] |
Hydro Weight: | 1565 lbs [709 kg] |
Drawbar capacity: | 570 lbs [258 kg] |
Front axle load: | 992 lbs [449 kg] |
Rear axle load: | 1,984 lbs [899 kg] |
Wheelbase: | 58 inches [147 cm] |
Length: | 103 inches [261 cm] |
Width: | 43 inches [109 cm], 36 inches [91 cm] (Narrow) |
Height (hood): | 43.6 inches [110 cm] |
Height (ROPS): | 78.9 inches [200 cm] |
Clearance (front axle): | 12.7 inches [32 cm], 12.3 inches [31 cm] (turf tires) |
John Deere 4100 Tires | |
Ag front: | 5.00-12 |
Ag rear: | 9.5-16, 8.00-16 (Narrow) |
Lawn/turf front: | 23x8.50-12 |
Lawn/turf rear: | 315x75D-15 |
Industrial front: | 23x8.50-12 |
Industrial rear: | 12.00x16.5 |
info | |
The model 410 loader fits the 4100 with four-wheel drive. |
Loader | |
Loader type: | John Deere 410 |
Height (to pin): | 74 inches [187 cm] |
Clearance, dumped bucket: | 55.1 inches [139 cm] |
Dump reach: | 24.8 inches [62 cm] |
Dump angle: | 45 |
Reach at ground: | 44.6 inches [113 cm] |
Rollback at ground: | 25 |
Rollback, raised: | 64 |
Breakout force (at pin): | 2,257 lbs [1023 kg] |
Breakout force (bucket): | 1,661 lbs [753 kg] |
Lift to full height (at pin): | 882 lbs [400 kg] |
Lift to full height (at 500mm): | 618 lbs [280 kg] |
Lift to 1.5m (at pin): | 1,072 lbs [486 kg] |
Lift to 1.5m (at 500mm): | 781 lbs [354 kg] |
Bucket width: | 49.2 inches [124 cm] |
Raise time to height: | 2.5 s |
Bucket dump time: | 2.0 s |
Lowering time: | 1.8 s |
Rollback time: | 1.9 s |